Info: '• For accurate results, NuvoLink SC must be connected to a properly terminated thinnet cable or Medium Attachment Unit, depending on configuration, before running the tests. '
4:
Bounds: x1=29, y1=141, x2=480, y2=191
Type: 8
Info: 'WARNING: Running these tests will briefly take NuvoLink SC off of the Ethernet network. Do not run these tests if you are logged onto a network server.'
5:
Bounds: x1=250, y1=248, x2=335, y2=264
Type: 8
Info: '--'
6:
Bounds: x1=250, y1=274, x2=336, y2=290
Type: 8
Info: '--'
7:
Bounds: x1=51, y1=274, x2=238, y2=290
Type: 8
Info: 'Thinnet Transceiver or MAU:'
8:
Bounds: x1=64, y1=248, x2=239, y2=264
Type: 8
Info: 'Serial Network Interface:'
9:
Bounds: x1=34, y1=221, x2=238, y2=238
Type: 8
Info: 'Network Interface Controller:'
10:
Bounds: x1=29, y1=16, x2=479, y2=65
Type: 8
Info: '• Clicking on the "Run Tests" button will run three separate loopback tests on the network hardware in the NuvoLink SC box and its connection to the network.'
DITL_18_Set Address.txt
Items: (12 entries)
0:
Bounds: x1=369, y1=184, x2=451, y2=205
Type: 4
Info: 'No Change'
1:
Bounds: x1=363, y1=224, x2=463, y2=246
Type: 4
Info: 'Set to Default '
2:
Bounds: x1=369, y1=258, x2=455, y2=281
Type: 4
Info: 'Change'
3:
Bounds: x1=17, y1=5, x2=472, y2=55
Type: 8
Info: '• Specifying an address in the "Change Address to:" edit area and clicking on "Change" will put an alternate Ethernet address in your System File.'
4:
Bounds: x1=40, y1=187, x2=216, y2=205
Type: 8
Info: 'Current Ethernet Address: '
5:
Bounds: x1=50, y1=228, x2=216, y2=246
Type: 8
Info: 'Built-In Default Address: '
6:
Bounds: x1=87, y1=262, x2=216, y2=280
Type: 8
Info: 'Change Address To:'
7:
Bounds: x1=221, y1=187, x2=325, y2=205
Type: 8
Info: ''
8:
Bounds: x1=222, y1=228, x2=326, y2=246
Type: 8
Info: ''
9:
Bounds: x1=17, y1=121, x2=475, y2=172
Type: 8
Info: 'WARNING: The default address built into NuvoLink SC is guaranteed to not conflict with other devices on your network. Don't change it without a good reason. '
10:
Bounds: x1=223, y1=262, x2=324, y2=278
Type: 16
Info: ''
11:
Bounds: x1=16, y1=63, x2=474, y2=113
Type: 8
Info: 'Note: Unlike the default address, the new address will not be "hard-coded" in the NuvoLink SC unit. It will be read from your System File and sent to the unit each time your Macintosh boots up.'
DITL_8_SC_NoDriver.txt
Items: (2 entries)
0:
Bounds: x1=112, y1=119, x2=172, y2=139
Type: 4
Info: 'OK'
1:
Bounds: x1=34, y1=64, x2=275, y2=114
Type: -120
Info: 'NuvoLink SC Setup was not able to open the NuvoLink SC driver in your System file.'